Semi-Automatic SMT Material Handling:
The Operator Moves, the System Confirms
No storage towers, no robots. Your operator registers, stores, picks, supplies, counts and returns every reel, while lights show where to go and sensors confirm each move. Neotel SMF software keeps the stock exact from goods-in to the line and back. Watch the whole loop in 3D.
- Reel registration in about 3 seconds, with a unique ID for every reel
- Pick-to-light with sensor confirmation: the lights find the reels, not the operator
- X-ray count in about 5 seconds per reel, written back to inventory
What is semi-automatic SMT material handling?
Semi-automatic SMT material handling is a way of running the SMT material flow in which operators carry and place the reels, while scans, light guidance and position sensors confirm every step. No storage tower or robot moves the material. In the Neotel setup, NEO SCAN registers each incoming reel with a unique ID, NEO LIGHT Plus racks and the NEO LIGHT Mobile Plus cart guide every put and pick by light, NEO COUNTER X400 counts returned reels by X-ray, and Neotel SMF software takes the work orders from your MES or ERP and keeps one inventory for all of it.
Watch the Semi-Automatic Material Flow in 3D
A schematic shop floor with one operator, light-guided racks and two SMT lines. Follow a reel from goods-in to the line and back to its slot. Play it from start to finish, jump to any step, or click a machine to learn more.
Who Does What: Operator and System
The operator does the moving. Scans, lights and sensors do the checking, so the inventory record always matches the shelf.
Registration
Storage and picking
Counting and return
How the Semi-Automatic Flow Works
The six steps of the animation, from goods-in to the line and back to the rack. Each one is run by Neotel SMF and done by your operator.
Registration: every reel gets an ID
Supplier reels arrive at goods-in. The operator lays each reel on the glass, a camera below reads the label and gives the reel a unique ID in about 3 seconds. A UID label is printed and applied, so traceability starts here.
Put-away: follow the light
SMF assigns a free slot and lights it blue. The operator puts the reel where the light is, and the position sensor confirms it: no scanning, no slot numbers to remember.
Picking: the work order into the cart
Your MES or ERP releases a work order and SMF works out which reels it needs. All its slots light up at once, first in, first out. The operator picks each reel into the NEO LIGHT Mobile Plus cart, and sensors confirm every pick and put.
Line supply: the cart becomes the line-side rack
The operator pushes the cart to the line and parks it there. Its slots light up for each reel to load onto the feeders, so no wrong reel reaches the line. Consumption is recorded in MES and SMF.
X-ray count: exact quantities for leftovers
At the end of the job the leftover reels go back into the cart and ride back to the racks. NEO COUNTER X400 counts each reel by X-ray in about 5 seconds and saves the quantity to its UID.
Return: back into a lit slot
The counted reel goes back into a lit cart slot, then from the cart into a lit rack slot. The sensor confirms it, stock matches the shelf again, and the loop is closed.
Trays Too: the Same Flow with NEO LIGHT HYBRID
Not every component comes on a reel. BGAs, QFPs and other packages often arrive in JEDEC trays, which are thin, look alike and are easy to misplace. NEO LIGHT HYBRID brings them into the same light-guided flow and the same SMF inventory as your reels.
- Register each tray with NEO SCAN, so every tray has its own ID.
- Map the trays to 5- or 10-tray carriers; each carrier has its own lit, sensor-checked slot.
- Search by tray ID and follow the light. When one tray is taken out, the carrier list stays exact.
- Count leftover trays in NEO COUNTER X400, laid in a single layer, and return them by light.
Reference configuration: 286 carrier slots for 2,090 JEDEC trays, sized to your tray volume. The animation shows reels only.
Explore NEO LIGHT HYBRID →
The Machines in the Semi-Automatic Setup
Start with one machine and add the others step by step. Every machine you add joins the same SMF inventory.
NEO SCAN
Manual reel registration station. A camera below the glass reads the supplier label and creates a unique ID in about 3 seconds per reel.
View product →
NEO LIGHT Plus
Fixed pick-to-light rack with a position sensor in every slot. Puts and picks are confirmed automatically, without a manual scan.
View product →
NEO LIGHT Mobile Plus
Lit rack on castors with a sensor in every slot. Takes a work order from the racks to the line and serves as the line-side rack.
View product →
NEO COUNTER X400
Offline X-ray component counter. Counts a reel in about 5 seconds and writes the quantity back to inventory.
View product →More NEO LIGHT models for stencils, moisture-sensitive reels (MBB) and JEDEC trays (HYBRID): see the NEO LIGHT series.
Semi-Automatic vs Fully Automatic Material Handling
The difference is who moves the material. Both setups run on the same SMF software, so you can start semi-automatic and add automation where it pays off.
| Semi-automatic | Fully automatic | |
|---|---|---|
| Registration | NEO SCAN: the operator places each reel | NEO SCAN PLUS: automatic batch scanning and labelling |
| Storage and picking | NEO LIGHT racks: the operator puts and picks by light. Trays: NEO LIGHT HYBRID | SMD BOX storage towers store and retrieve on their own. Trays: SMD BOX HYBRID |
| Line supply | NEO LIGHT Mobile Plus cart, pushed by the operator | Automatic kitting and AGV transport |
| Counting | NEO COUNTER X400, offline | NEO COUNTER X800, inline |
| Typical fit | High-mix production, small to medium lines, line-side kitting | Central warehouses, large-scale lines, unmanned operation |
Semi-Automatic SMT Material Handling FAQ
Common questions about running the SMT material flow with light-guided racks and an operator.
What is semi-automatic SMT material handling?
It is a way of running the SMT material flow in which operators carry and place the reels, while scans, light guidance and position sensors confirm every step. In the Neotel setup, NEO SCAN registers incoming reels, NEO LIGHT racks guide storage and picking, NEO COUNTER X400 counts returned reels by X-ray, and SMF software keeps one inventory.
What is the difference between semi-automatic and fully automatic material handling?
The difference is who moves the material. In a semi-automatic setup the operator puts and picks reels by light, with no storage towers or robots. In a fully automatic setup, SMD BOX storage towers store and retrieve reels on their own and can run unmanned. Both run on the same SMF software, so you can start semi-automatic and upgrade later.
Which factories is semi-automatic material handling suited to?
It suits high-mix production, small to medium lines, line-side kitting and prototype or NPI lines. It needs a lower investment and is quick to deploy. Factories with large-scale lines or unmanned operation usually choose the fully automatic route. If you are unsure, start with one step of the material loop and add more later.
Does the operator still have to scan every reel?
Only at registration. Once NEO SCAN has given a reel its unique ID, NEO LIGHT Plus racks and the NEO LIGHT Mobile Plus cart confirm every put and pick with position sensors. There is nothing to scan and no slot number to remember.
How are JEDEC trays handled?
Trays are registered with NEO SCAN and stored in NEO LIGHT HYBRID. Each tray is mapped to a 5- or 10-tray carrier, and each carrier sits in a slot with its own light and position sensor. You search by tray ID and follow the light. Trays and reels share one SMF inventory.
Is it safe to work next to the NEO COUNTER X400?
Yes. Counting takes place inside a fully enclosed, lead-shielded cabinet with a safety interlock, so the X-ray source only emits when the cabinet is closed. Operators can work beside the machine throughout the shift.
Can I start with just one machine?
Yes. Many factories start with NEO LIGHT racks to end the search for reels, then add NEO SCAN registration and NEO COUNTER X400 counting. All data sits in SMF, so every machine you add joins the existing inventory.
Does it connect to our MES or ERP?
Yes. SMF takes the work orders from your MES or ERP and reports stock and consumption back, through standard interfaces or the database. Your MES or ERP stays the source of orders and master data. The scope of the integration is agreed per project.
Plan Your Semi-Automatic Material Flow
Tell us how many reels and trays you store, how many lines you run and which MES or ERP we should connect to. Our engineers configure the racks, slots and machines for your material mix.